Journal #35: Trimmed Out

by Miles Raymer

Trimming is an activity in which the artful reduction of an object often constitutes a simultaneous increase in that object’s value––a shuffling off of excess matter in order to highlight what remains.  A trimmed hedge gains aesthetic appeal. A trimmed physique imbues confidence and attracts potential mates. A trimmed intellect communicates with clarity and poise.

For a house, trim is a feature that implies completion. The trim itself is an addition to the structure, which can make it easy to forget that those components are all cut from larger boards, which are themselves milled from tree trunks. We pare down reality to focus attention and appreciate detail.

For the last week and a half, we’ve accomplished a lot on the new addition, but the most interesting process for me was learning how to trim interior windows and doors. Sean, a consummate perfectionist, began this process by showing Matt how to insert shims between the window and wood frames. This ensured that the trim nailed to these shims would produce a smooth, straight reveal.

Shims in

Shims in

Next, we cut and secured the window sills with the finishing nailer. The sill edges come prefinished, so all we had to do was notch them to fit around the windows.

Installing the sill

Installing the sill

Next, we cut and nailed trim pieces for the top inside section.

Top piece in

Top piece in

Then the sides.

Inside trim done

Inside trim done

In this picture, you can see how the shims guide the trim to expose the same width of window frame all the way around.

Next, we covered the side joints with another layer of trim. We nailed each of these pieces to reveal exactly 1/4″ all the way around, creating a second reveal thinner than but consistent with the first one.

Sides trimmed

Sides trimmed

Sean likes to trim windows using a top bead that mirrors the bottom sill, which is also the style Jessie prefers. So, before we put the header on, we made beads using some cedar that was left over from the exterior trim. Sean used a special saw to give the board a curved edge, and then used the table saw to cut that edge into a long bead.

First cut

First cut

Second cut

Second cut

After sanding the beads down on both sides, we could cut and nail them to the top trim pieces.

Beads ready

Beads ready

We cut the beads 1/2″ longer than the top trim pieces so they would hang over 1/4″ on each side. This is the same overhang as the bottom sill.

After putting in the top trim, all we had to do was add a piece below the sill for a nicely trimmed interior window.

Trim done

Trim done

After everything was nailed, we caulked every joint to give the trim a seamless finish.

Trimming strikes me as a task that’s easy and quick when done carelessly, but involved and meticulous when done right. The final product of a detailed job is very satisfying. Having participated in the process of trimming my own home, I’ll always be able to remember the thought and care that went into an aspect of building I’ve always taken for granted.

Trimming was far from the only thing keeping us busy during the last ten days. Early last week, Matt and I finished the new deck railing while Sean painted the house interior.

Matt working on deck railing

Matt working on deck railing

Blocks are useful for making sure these rods are evenly spaced. It takes a few tries to figure out precisely which size gap (starting at a maximum of 4″ and working down) will work out evenly for any given span of railing, but once you have your number, then one block will get you through the whole section.

Railing done

Rods in

After finishing the rods, I made top caps for these rails out of 2″x6″ redwood, cutting the ends at 45 degree angles where they butt up against the posts for the roof overhangs.

Railing done

Railing done

Meanwhile, Sean transformed our newly-textured sheetrock into painted walls.

Textured living room

Textured living room

Painted living room

Painted living room

Textured bedroom

Textured bedroom

Primed bedroom

Primed bedroom

Painted bedroom

Painted bedroom

Painted bathroom

Painted bathroom

Jessie did a wonderful job choosing the colors, and seeing the painted walls marked a big milestone in our excitement about the project’s near completion. It also marked a change in the experience of working on the house interior. Suddenly surrounded by newly-finished surfaces, we have to take extra care when wielding our tools and bodies. Things will get even trickier when we begin installing the wood floor.

Another surface that received its last layer was the exterior cedar ceiling. Sean chose a simple clear coat that beautifully highlighted the wood’s natural grain.

Cedar with clear coat

Cedar with clear coat

Second layer applied for long-lasting protection

Second layer applied for long-lasting protection

We also cut the solar tubes into the ceiling last week. This began with going up to the new attic to measure the midpoint of the rafter bays. Using nails Sean had put through the sheetrock as a reference, I located the centers for our circular cuts.

Measuring the bays

Measuring the bays

Sean used my nails to draw a circle on the ceiling’s surface, which I then cut out using a special sheetrock saw.

Sean installing the tube casing

Sean installing the tube casing

Three tubes installed

Three tubes installed

These tubes are a terrific source of natural light, even on a cloudy day. I’m especially impressed with how bright they are, given that they’re installed on the north side of our roof.

On Monday, we finished trimming the windows and Sean showed Matt and me how to install an interior door. The key is to make sure the side with the hinges gets nailed to a perfectly plumb surface (shims can be used if the edge of the door jamb needs adjustment). In our case, no shims were necessary.

Fitting the interior door into the jamb

Fitting the interior door into the jamb

Once the hinge side was nailed, we used shims to even out two sides of the door frame. The important part here is to make sure the top of the frame is nicely leveled with the header above the jamb.

Shims in

Shims in

Next, we cut off the ends of the shims and trimmed the door in pretty much the same style as the windows, caulking all the joints when finished.

New bedroom door, installed and trimmed out

New bedroom door, installed and trimmed out

On Monday, we also welcomed Larry and his tractor back to the site to get things ready for our final concrete pour. This thin slab will provide a walkway up to both front doors and also a smooth ramp up to the new garage.

Larry grading space for the final slab

Larry grading space for the final slab

Yesterday’s main task was to set our drainpipes, which will hook up with the new gutters and direct water toward the north end of the property. We didn’t have to trench too much because most of the drains will get covered with concrete, but we did have to make sure the drains had an adequate grade to promote downward flow.

Getting started

Getting started

Pipes to the new gutters

Pipes to the new gutters

Sean craftily connected this new gutter to one of our old drains

Sean craftily connected this new gutter to one of our old drains

Drain heading north in front of the garage

Final section heading north in front of the garage

It is supposed to rain tomorrow, so hopefully we’ll be able to see how well the drain functions before covering it up. Ma and I would eventually like to install a roof-water capturing system for garden irrigation, but for now a traditional drain system will have to do. Fortunately, the northern end of our property is a natural wetland area that drains into Mill Creek, so sending water that way conforms to the natural landscape.

Keeping up with this project’s final stages is exhausting, and it’s easy to get hurt when I don’t pay attention. In a new chapter of my ongoing struggle to be more mindful of my physical safety on the job, I strained my back while loading debris for a dump run last Monday. Fortunately it’s nothing too serious or permanent, so the experience has humbled me in a good way. Still, I can’t believe my luck: even as it trims away some of my physical strength and throws in a little pain, life brings me a few steps closer to having a new home.